بردکنترلر MKS SBase V1.3 32Bit یک مادر برد چاپگر سه بعدی است که توسط شرکت (MKS) Maker base طراحی شده است و بر اساس پلت فرم (ARM) است و مجهز به پردازنده  32bit 100M Cortex-MS MCU-LPC1768  است   

برد PCB چهار لایه با کیفیت بالا و بهینه سازی حرارت

پشتیبانی از سیستم عامل منبع باز بسیار مدولار

مجهز به پردازنده  32bit 100M Cortex-MS MCU-LPC1768

استفاده از تراشه قدرت اختصاصی  برای پشتیبانی از ورودی برق 12V-24V

استفاده از درایور استپر موتور DRV8825 که از 32 میکرو استپ پشتیبانی می کند و دارای خنک کننده عالی است

MKS SBASE V1.3 32-bit Open Source for Smoothieware 3D Printer Controller Board
Using 32-bit 100M Cortex-M3 LPC 1768 master chip, performance greatly improved.
Support a high degree of modular open source firmware to facilitate the secondary development, eliminating the need to grasp the core code to worry about.
Support network function, through the network cable can be directly connected to the network, the use of the browser can achieve remote control.
Using 8825 as a motor driver to support 32 subdivision, performance far more than 4988, using SOP package, better heat dissipation.
The stepper motor current is set directly without worrying about damaging the drive or potentiometer when adjusting the current.
The circuit board uses high-quality 4-layer board, and specially made heat optimization.
Using a dedicated power chip to support 12V-24V power input.
Can be connected to 12864LCD.
Touch screen MKS TFT28.
Pre-use instructions:

Before powering on, do confirm whether the positive or negative is connected correctly. Problems due to user's reverse connecting of the burned power does not belong to warranty.
Please do not plug the motor when it is powered on. It is easy to cause burned drive. Do not run the motor in the process of adjusting the current. The correct way is that first disconnect the power, unplug the motor, and then re-power, adjust the potentiometer, measure the voltage on the potentiometer until the measured voltage is the same as expected.
At present, MKS SBASE only support TFT series and LCD12864 display, not 2004, OLED display.
Specifications:

Model: MKS sbase v1.3
Power input: 12-24V
Driver chip: DRV8825

MKS-SBASE Mainboard

Overview:
 
 MKS-SBASE is the latest motherboard for 3D Printer, designed by Makserbase (MKS).
 It is based on ARM platform and uses  32bit 100M Cortex-MS MCU-LPC1768
 
Features:
 
 Using 32bit 100M Cortex-M3 MCU-LPC 1768, and improve its performance highly.
 Support highly modular open source firmware, easy for secondary development.
 Support network function, then proceed remote control via IE Explorer.
 Using DRV8825 stepper driver which supports 32-microstep and with excellent cooling.
 Currents of the stepper motor can be set directly, which can avoid the damage.
 Using high-quality FR-4 4 layers PCB and special design for cooling.
 Using professional power chip, support 12V-24V DC input.
 Good to work with LCD12864 and MKS TFT touchscreen.
(Can't work with MKS MINI12864LCD, OLED12864, and LCD2004 display.)